Vxl120m Rear Support Engine Route For Opel, Opel Astra 2.0t Mk5 Vxr Zafira

Vxl120m rear engine support road for Opel, Opel astra 2.0t mk5 vxr zafira. This product sheet is originally written in English. Please find below a machine translation in French. If you have any questions please contact us. Vxl120m rear engine support for road, Opel astra 2.0t mk5 vxr zafira 2.0t.

Vxl120m vibra technologies road engine mount road for Opel, Opel astra mk4 (g) 2.0 turbo, astra mk5 (h) vxr, zafira 2.0 turbo. Quantity required for the car: 1. Product notes: rear engine support. Please note that this purchase is for. If you need a supplement.

Get the right piece for the first time. Please make sure to check the notes section on the left-hand table of compatibility. On most websites providers, there are now additional webcats so that you can check your application with more information shown to make sure it's correct for the bike - please check the manufacturer's websites as well. In case of doubt, please request or contact the customer services under the information of the business vendor at the bottom of each advertisement.

What are the advantages of using vibra-technics engine supports? Our products are designed to deliver uncompromising performance.

Other benefits include better handling and driver feel. Reduced overall engine movement significantly reduces the stress on engine connections such as intermediate cooling pipes, fuel lines, exhaust systems, etc. The game between the engine and other critical parts such as a support leg interlock and other parts under the hood is maintained. What is the difference between a "road" mount and a "competition" mount?

Engine mounting systems are a balance between the isolation of engine vibrations and the control of engine movements. The engine mounting system is indeed an engine suspension system. Its geometry can be as critical as the main suspension system of your car. The same factors affect its performance, damping of stiffness, bending, etc.

When we design a system, we return to the first principles of vibration insulation, to make sure we develop something that has the main function of isolating the vibrations of your motor. The main difference between a "road" system and a "competition" system is the point at which they isolate the vibrations of the engine.

Road systems must isolate vibrations until idle, which is extremely difficult to achieve while controlling the movement of the engine and requires careful adjustment of the rigidity of the support. Be aware that the "road" supports are more rigid than the original equipment and can therefore produce perceptible vibrations. Competition systems have a isolation threshold of more than 3000 rpm, below which the vibrations transmitted can still be quite high.

This allows us to make the system much more rigid to control the movement of the engine at least, usually less than 3 mm (compared to 25-30 mm for an oem system). How do motor supports improve manoeuvrability? The engine and transmission are usually a mass of 200 kg and more swinging under the hood of your car as a pendulum on its original supports. There are two main ways to affect manipulation.

1 physical movement of supports under extreme acceleration, braking and bend. This actually moves the center of gravity of the car in the worst possible direction. This can seriously affect the balance of the car at the most critical time. When you control this physical movement of transmission, this can significantly improve the accuracy of handling, especially on a car using tires and competitive suspensions.

2 secondary driving, sometimes referred to as "engine crash", is the movement of the engine caused by the hump inputs of the main suspension system, oscillating the engine on its supports. In extreme cases, it may be a feeling of unpleasant noise. The very large mass of the engine that will tremble will cause unwanted dynamic forces on the car. What kind of supports do I need for my car track day? This depends in large part on why you use the car.

If it is used as a road car during the week, we suggest that you use specified supports as a "road". They are more than able to manage the abuse of a day on track and would be considerably more robust than the original supports. Performance and manoeuvrability will be considerably improved. If your car is used only during the days of the track and is not used on the road, try the "competition" supports for a real feeling of racing car. I saw the term "nvh" used.

Nvh is a widely used term in the automotive industry to describe the quality of noise and vibration inside a car. "Noise" and "vibration" are measurable values but "hardness" is very subjective.

The purpose of an engine mounting system is to reduce the nvh to an acceptable level. The ultimate goal is to make the engine in motion imperceptible to the driver and passengers. In reality, this requires significant compromises in the control of engine movements and durability. Vibra-technics engine supports are designed to deliver excellent nvh performance without compromising engine control. What are the causes of engine vibrations?

There are two main causes of engine vibration, the engine imbalance forces and the torsion vibrations resulting directly from the ignition of the cylinder. Depending on the engine configuration, the vibrations caused by the engine imbalance can be in any 1 or a combination of 6 main axes.

Linear; vertical, lateral and longitudinal. Rotation; roll, pitch and yaw.

Some engine configurations are inherently extremely well balanced, such as in-line 6-cylinder engines, and some are very poor, such as the 4 in-line. High-cylinder 4-cylinder engines (2.0 l or more) suffer from a high vibration level that occurs at twice the engine speed, known as second-order imbalance.

This often translates into a booming noise in the car that can be heard at high engine speeds. In many cases, engine designers have incorporated a balance (rotation of the shaft at twice engine speed) to cancel these forces. The v8 engines with a multi-plane crankshaft and a 90-degree v-angle are actually 4 v-jumps connected end to end. These are well balanced and produce low levels of vibration. That's why this is the most popular configuration for a serial v8.

A high performance race v8 with a flat crankshaft has the same second-order imbalance problem as a 4-cylinder engine in line. Flat crank v8 are used by ferrari, tvr ajp v8, lotus spirit v8 and the new mp4 12c mclaren. Torsion vibrations caused by the firing of cylinders usually generate a problem at very low engine speed where the amplitude can be quite high and the frequency relatively low. This can cause an unpleasant shaking in the car at idle.

Do you only make black rubber supports or can I have other colors? As Henry Ford said, "you can have any color you like while it's black." We use the same principle, for almost the same reason! The black color is carbon.

As with other carbon engineering and automotive applications, it is used to control some of the most critical features. In the case of rubber, it is strength, stiffness, resistance to abrasion, etc. At the time of Henry Ford, it was used as a pigment to make black enamel paint. At the beginning of the last century, resin-based paint containing carbon was a much more durable and dried finish faster than other colors, so painting all cars in black was a faster process.

The time taken to paint a car was a bottleneck in the production of the model t, so henry normalized on the black! We don't have to worry about speed, but the increased durability and resistance you get from carbon are important. Rubber can be moulded in other colours but at the price of some important features.

We make no compromises on performance, so we only use black rubber! Why do you use rubber instead of urethane?

We use the best available materials and technologies to do the job! Urethane is superior to rubber in its resistance to abrasion and chemicals, which is why it is used in tires for forklift trucks, mudguards, etc.

Oems sometimes use it for suspension stops because of its resistance to abrasion. It is also much more economical to manufacture as it is also available as a coulable resin, so mould tooling is much cheaper. Rubber moulding requires specialized injection moulding tools and high-pressure and high-temperature moulding machines. For engine mounting applications, natural rubber or natural/synthetic mixed rubber is superior to urethane in all respects.

# Resilience (rigidity / damping ratio). # creep and permanent grip (permanent deformation). One of the many critical weaknesses of urethane as an engine mounting material is the change in characteristics over a temperature range, especially its resilience. The engine compartment is subjected to extreme temperature ranges. Urethane is unstable under these conditions. This is why oem never use urethane for a main engine mounting system. Our policy is an uncompromising and ultimate engine mounting solution.

If urethane was the best substance to use, we used it! My application is not listed, are you making one-time projects? Due to the way many car manufacturers now use global platforms, we can already create a suitable support for your application that is used on another vehicle. Let us know what you're driving and we'll see if we have anything that's right. Developing a complex customised one-time system can be costly.

Before the first prototypes were available for vehicle testing, it took up to 200 hours of work in the R&D phase. However, we are still interested in new applications, so please contact us with your needs and we will see if it is viable for us to do so.

The future applications that we will review once we have resolved the current backlog are as follows. Toyota supra'95 -'97.

If you have one and want to be part of the development program, let us know. If you also need another suspension ring, please. Thank you very much for your interest. For more details on our delivery options and costs, please click here. For more details on our return policy, please click here.

Do not hesitate to contact us to discuss any topic on which you may have a question. We are proud of a quality service and are pleased to respond to all your concerns. Add our store to your favorites and receive e-newsletters about new items and special offers. The item "vxl120m rear engine support road for Opel, Opel astra 2.0t mk5 vxr zafira" has been on sale since Tuesday, May 4, 2021. It is in the category "auto, motorcycle - parts, accessories\tuning, styling\motors, chip tuning\motor supports".

The seller is "mjd128" and is located at/in leatherhead. This item can be delivered anywhere in the world.

piece manufacturer: vibra technics